Operating Instructions Four 4 in 1 Cable Remote Control UR4-DCT
CABLE : Cable Converts
TV : Televisions
VCR : VCRs and DVD
AUX : Audio Receivers, DMX & DCR, TIVO, etc.
For TV/VCR combination unit, use following steps to operate the Volume control.
Press the [CBL] button and the [OK] button simultaneously for 3 seconds. The [CBL] button will light on for 20 seconds.
Press the [VOL+] button.
Press the [VCR] button. The LED will blink twice to confirm the programming.
Default State
Device Default: Motorola DCT series and CFT2200.
Channel Default: CABLE channel and number keys through the CABLE, with the option of controlling channel and number keys through the TV or VCR. Refer to section F for programming the channel and number keys through your TV or VCR.
Volume Default : CABLE volume and mute through the CABLE , with the option of controlling volume and mute through the TV or AUDIO.
System On/Off button
This button is designed to send out power commands for two, three or all four devices with one button press.
Three-Digit Code Programming Method
The
remote control can be programmed by pressing in a three digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment.
The three-digit code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX).
STEP2 Press the [DEVICE] button (TV, VCR or AUX) to be programmed and the [OK] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed.
*Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.
*Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [POWER] button, the equipment
should turn on or turn off.
*Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
*Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat fromStep 3 using the next three-digit code number from the same brand list.
The three-digit code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX).
STEP2 Press the [DEVICE] button (TV, VCR or AUX) to be programmed and the [OK] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed.
*Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.
*Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [POWER] button, the equipment
should turn on or turn off.
*Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.
STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.
*Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat fromStep 3 using the next three-digit code number from the same brand list.
Auto Search Method.
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
STEP1 Turn on the equipment you wish to operate.
STEP2 Press the [DEVICE] button (TV, VCR or AUX) to be programmed and the [OK] button simultaneously for 3 seconds. The device LED will turn on.
*Tip : The device LED will light on for 20 seconds. The next step must be entered while LED is on.
STEP3 Press the [CH+] or [CH-] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH+] or [CH-] button as soon as the equipment turns off.
*Tip : You can verify that you selected the correct code by pressing the [POWER] button. The equipment should either turn on or turn off.
STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
To Find the Three Digit Code Number That was Stored in theDevice.
STEP1 Press the [DEVICE] button (TV, VCR or AUX) you wish to verify and the [OK] button simultaneously for 3 seconds.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on.
STEP2 Press the [INFO] button.
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
STEP1 Turn on the equipment you wish to operate.
STEP2 Press the [DEVICE] button (TV, VCR or AUX) to be programmed and the [OK] button simultaneously for 3 seconds. The device LED will turn on.
*Tip : The device LED will light on for 20 seconds. The next step must be entered while LED is on.
STEP3 Press the [CH+] or [CH-] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH+] or [CH-] button as soon as the equipment turns off.
*Tip : You can verify that you selected the correct code by pressing the [POWER] button. The equipment should either turn on or turn off.
STEP4 Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
To Find the Three Digit Code Number That was Stored in theDevice.
STEP1 Press the [DEVICE] button (TV, VCR or AUX) you wish to verify and the [OK] button simultaneously for 3 seconds.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on.
STEP2 Press the [INFO] button.
The
device LED will blink number of times indicating the number of each digit of
the code number. Each digit is separated by a 1second interval of the LED being
turned off.
Example : One blink, three blinks and eight blinks with an interval of 1second of LED being turned off,indicates the code number 138.
Note : Ten blinks is equal to the number 0.
Example : One blink, three blinks and eight blinks with an interval of 1second of LED being turned off,indicates the code number 138.
Note : Ten blinks is equal to the number 0.
Programming a second TV to AUX Mode.
STEP1 Press the [AUX] button to be programmed and the [OK] button simultaneously for 3 seconds.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on.
STEP2 Press the [TV] button to pick up the TV code table.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables.
STEP4 Store the three-digit code number by pressing the [AUX] button once again. The device LED will blink twice to confirm that the code has been stored.
Programming The System On/Off Button.
This is designed to program the System On/Off button so that it can send out up to four power on/off commands with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM] button and the [OK] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.
STEP3 Press the [DEVICE] button and the [POWER] button you wish to store in the System On/Off button and repeat this until you stored all the power commands into the System On/Off button.
STEP1 Press the [AUX] button to be programmed and the [OK] button simultaneously for 3 seconds.
*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on.
STEP2 Press the [TV] button to pick up the TV code table.
STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables.
STEP4 Store the three-digit code number by pressing the [AUX] button once again. The device LED will blink twice to confirm that the code has been stored.
Programming The System On/Off Button.
This is designed to program the System On/Off button so that it can send out up to four power on/off commands with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM] button and the [OK] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.
STEP3 Press the [DEVICE] button and the [POWER] button you wish to store in the System On/Off button and repeat this until you stored all the power commands into the System On/Off button.
STEP4
Press
the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm
the saving.
Programming Channel Control.
By following the steps below, the user can program the channel controls (channel UP, and channel DOWN) from one device to operate in another device mode. The default channel control settings on the remote control is as follows:
CBL : CBL T V : CBL
VCR : VCR AUX : AUX
If you wish to store the TV channel control in TV mode, use the following steps.
STEP1 Press the [TV] button and the [OK] button simultaneously for 3 seconds.
*Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL -] button.
STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming.
To return to original state:
If you wish to restore the CABLE channel control in TV mode, repeat the above steps by pressing [CBL] in STEP3 .
Programming Volume Control .
By following the steps below, the user can program the volume controls (Volume UP, Volume Down and MUTE) from one device to operate in another device mode. The default volume control settings on the remote control is as follows :
CBL : TV TV : TV
VCR : TV AUX : AUX
lf you wish to store the TV volume control in CBL mode, use the following steps.
STEP1 Press the [CBL] button and the [OK] button simultaneously for 3 seconds.
By following the steps below, the user can program the channel controls (channel UP, and channel DOWN) from one device to operate in another device mode. The default channel control settings on the remote control is as follows:
CBL : CBL T V : CBL
VCR : VCR AUX : AUX
If you wish to store the TV channel control in TV mode, use the following steps.
STEP1 Press the [TV] button and the [OK] button simultaneously for 3 seconds.
*Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on. STEP2 Press the [VOL -] button.
STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming.
To return to original state:
If you wish to restore the CABLE channel control in TV mode, repeat the above steps by pressing [CBL] in STEP3 .
Programming Volume Control .
By following the steps below, the user can program the volume controls (Volume UP, Volume Down and MUTE) from one device to operate in another device mode. The default volume control settings on the remote control is as follows :
CBL : TV TV : TV
VCR : TV AUX : AUX
lf you wish to store the TV volume control in CBL mode, use the following steps.
STEP1 Press the [CBL] button and the [OK] button simultaneously for 3 seconds.
Tip : The device LED will light
on for 20 seconds. The next step must be entered while the LED is on.
STEP2 Press the [VOL +] button.
STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming.
To return to original state:
If you wish to restore the CABLE volume control in CBL mode, repeat the above steps by pressing [CBL] in STEP3 .
STEP2 Press the [VOL +] button.
STEP3 Press the [TV] button. The device LED will blink twice to confirm the programming.
To return to original state:
If you wish to restore the CABLE volume control in CBL mode, repeat the above steps by pressing [CBL] in STEP3 .
Programming For Advanced Function.
In the CABLE mode, the A, B and C buttons can be programmed to act as a macro or favorite channel button to send out up to 10 commands with one button press.
STEP1 Press the [CBL] button to select the CABLE mode
STEP2 Press the [A (or B,C)] button and [OK] button simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds.
STEP3 Press up to 10 buttons you wish to store. The CBL device LED will blink once for each command entered.
STEP4 Press the [CH+] button to store the functions that are selected. The CBL device LED will blink twice to confirm the storage of functions.
LOW BATTERY WARNING.
When the battery is low and needs to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.
In the CABLE mode, the A, B and C buttons can be programmed to act as a macro or favorite channel button to send out up to 10 commands with one button press.
STEP1 Press the [CBL] button to select the CABLE mode
STEP2 Press the [A (or B,C)] button and [OK] button simultaneously for 3 seconds. The CBL device LED will turn on for 20 seconds.
STEP3 Press up to 10 buttons you wish to store. The CBL device LED will blink once for each command entered.
STEP4 Press the [CH+] button to store the functions that are selected. The CBL device LED will blink twice to confirm the storage of functions.
LOW BATTERY WARNING.
When the battery is low and needs to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.
Memory Lock System.
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
