Used
Ics: TLO74, UPC1237HA, IC4558, STK4151, UPC1298V
200
watts
Front channels – 35 watts x 3 @ .1% THD
Surround channels – 15 watts x 2 @.1% THD
Subwoofer – 65 watts @ .1% THD
Front channels – 35 watts x 3 @ .1% THD
Surround channels – 15 watts x 2 @.1% THD
Subwoofer – 65 watts @ .1% THD
If
there is no sound from any of the speakers, check the following
•
Make sure the subwoofer is plugged into an active AC wall outlet.
• Make sure the Master Power Switch, located on the rear of the subwoofer, is in the “On/Standby” position.
• Make sure there is a source – for example, a VCR or television – hooked up to the TV or tape/aux input jacks on The Source.
• Make sure that the program material is playing.
• Recheck the hookup connections.
If most of the sound comes from the center-channel speaker, with little or no information from the surround channels, note the following:
• Make sure the Master Power Switch, located on the rear of the subwoofer, is in the “On/Standby” position.
• Make sure there is a source – for example, a VCR or television – hooked up to the TV or tape/aux input jacks on The Source.
• Make sure that the program material is playing.
• Recheck the hookup connections.
If most of the sound comes from the center-channel speaker, with little or no information from the surround channels, note the following:
Although
most of today’s televisions are equipped with stereo audio output jacks, some
stereo televisions have poor audio sections and are unable to provide a Dolby
Pro Logic encoded signal. In the unlikely event that you experience this
problem, connecting the audio outputs from your hi-fi VCR, laser disc player,
DVD player, or satellite receiver directly to one of the inputs on The Source
will provide a proper audio signal and allow you to enjoy true Dolby Pro Logic
surround sound.
If there is no sound from the surround speakers or sound is very low, check the following:
• Check all connections between the amplifier and each of the speakers.
• Raise the surround volume from the remote control
• Make sure the TV show or movie you are watching is recorded in Dolby Surround.
If there is no sound from the center speaker, check the following:
• Make sure that the processor is in the Pro Logic mode. If it is in Phantom or Stereo mode, the center speaker will not play.
• Check the connections between the subwoofer and the center speaker.
If there is no sound from the surround speakers or sound is very low, check the following:
• Check all connections between the amplifier and each of the speakers.
• Raise the surround volume from the remote control
• Make sure the TV show or movie you are watching is recorded in Dolby Surround.
If there is no sound from the center speaker, check the following:
• Make sure that the processor is in the Pro Logic mode. If it is in Phantom or Stereo mode, the center speaker will not play.
• Check the connections between the subwoofer and the center speaker.
If
you have low bass output, check the following:
• Experiment with placement of the subwoofer. Remember, place the subwoofer in a corner to get maximum bass output from the system.
• Increase the level of bass, using the remote control.
• Adjust the level control on the rear of the subwoofer.
If you are having trouble picking up radio stations, check the following:
• Make sure the antenna is hooked up properly.
• Depending on your distance from the station’s transmitter, you may need to install an FM antenna on the roof or in the attic.
• Experiment with placement of the subwoofer. Remember, place the subwoofer in a corner to get maximum bass output from the system.
• Increase the level of bass, using the remote control.
• Adjust the level control on the rear of the subwoofer.
If you are having trouble picking up radio stations, check the following:
• Make sure the antenna is hooked up properly.
• Depending on your distance from the station’s transmitter, you may need to install an FM antenna on the roof or in the attic.
Schematic
[Circuit diagram]
