Electrohelponline: URC200014 Remote control Set-up procedure

Vodafone TV Digital Recorder 2014 – Set-up Procedure

Find the brand of your television in the Set-up Code section and select the first 4 digit code in the list. Switch on your TV (not on standby).

Press the TV key and release it.

Press and hold down the Now’s Good key until the red LED underneath the TV key lights up twice.

Enter the 4-digit code for your television (the red LED should light up twice after having entered the fourth digit).

Press the Power key and see if you are able to switch off your television.

If your television does not respond, repeat steps with each code listed for your brand. If none of the codes listed for your brand operate your television, or if your brand is not listed, try the code search described.

Switch your television back on by pressing a number key (or CH+) and check if all the functions are working correctly.

Write down the code for your television on the inside of the battery cover for quick easy reference.

Programming Notes

• If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote.
• Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.

This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device.

Code search

If your device does not respond to the DTR remote after having tried all the codes listed for your brand, you can try the Code search. During the Code search you will run through every available code in the DTR remote library. This method may also work if your brand is not listed at all.

To search for your television code.

Make sure that you television is switched on.

Press the TV key and release it.

Press and hold down the Now’s Good key until the red LED (underneath the TV key) lights up twice.

Press 9 9 1. The red LED will light up twice.

Aim the DTR remote at your device.

Next press power.

Aim the DTR remote at your Television. Now press CH+ over and over, until your Television turns off.

Every time you press the CH+ key the DTR remote will send out a POWER signal from the next code contained in the PVR library.

You may have to press this key many times (up to 150 times) so please be patient. The Code search can take approximately 15 minutes.

If you skip past a code, you can go to the previous code(s) by pressing the CH- key. Remember to keep pointing the remote at your device during the Code search.

As soon as the device switches off, press Now’s Good key to store this code.

Important: Press the corresponding device key when doing a Code search. If your device does not have a POWER key, press PLAY instead.

Blink out your code

By blinking out you code you can determine which code is actually working for your device.

Example: To blink back the code for your television.

Press the TV key and release it.

Press and hold down the Now’s Good key until the red LED (underneath the TV key) lights up twice.

Press 9 9 0. The red LED (underneath the TV key) will light up twice.

Press 1 and count how may times the LED lights up. If it does not light up the first digit is 0.

Press 2 and count how may times the LED lights up. If it does not light up the second digit is 0.

Press 3 and count how may times the LED lights up. If it does not light up the third digit is 0.

Press 4 and count how may times the LED lights up. If it does not light up the fourth digit is 0.
Now you have found the 4-digit code.

Important:
- If during step 4, 5, 6 or 7 the LED does not light up at all, the digit is 0.
- Press the corresponding device key during step 1 if you want to blink back the code for another device you programmed.

Volume lock

The DTR remote comes with a “Volume Punch Through” feature. This allows you to control the TV volume also if you are in “PVR” or “DVD/VCR” mode.

“Volume Punch Through” can be cancelled for a specific mode.

To cancel the “Volume Punch Through” for DVD mode:

Press DVD

Press and hold down the Now’s Good key until the red LED underneath the DVD key lights up twice.

Press 9 9 3.

Then press the VOL (-) key and the LED will light up four times.

To cancel the “Volume Punch Through” for all modes:

Press and hold down the Now’s Good key until the LED (underneath TV or DVD key) lights up twice.

Press 9 9 3.

Then press the VOL (+) key and the LED will light up four times.