PROGRAMMING PROCEDURE
SET-UP Code list are given by the previous post here.
DIRECT CODE ENTRY METHOD (Set-up codes for TVs are given by previous post here)
> Locate the Remote Code List provided in this manual. Find the DEVICE
CATEGORY you wish to program (for example TV, DVD, CBL/SAT, DVR/AUX)
and then fid the BRAND of that device. Circle all the codes under that
brand. Example: For a GE TV, locate the TV code section then circle all of the
GE TV codes. [Visit the previous post here to get set-up codes]
> Manually turn on the device you wish to control.
> Press and hold the SETUP button until the red indicator
light stays on (approximately 4 seconds) and then release the SETUP button.
> Press and release the desired device button on the remote (TV,
DVD, CBL/SAT, DVR/AUX). The red indicator will blink once and then remain
on.
> Enter the fist 4-digit code previously found in the code list
using the number buttons on the remote. If the code entered is a valid code,
the red indicator light will turn off. If the code entered is not a valid code,
the red indicator light will flash and remain on allowing you to re-enter the
code.
[If no buttons are pressed for 10 seconds, the remote will exit
the SETUP mode and you will have to start over.]
> Point the remote at the device. Press the POWER button—if
the device turns off, no further programming is required for that device. If
the device does not turn off, return to step 3 and use the next code found in
the code list. Continue this process until a code for your device is found.
> Repeat this process for each device (for example TV, DVD,
CBL/SAT, DVR/ AUX) in your home entertainment system you wish to control.
Four devices can be programmed.
{{* If your device does not respond to the remote after trying all
codes listed or your brand is not listed in the code list, use the Auto Code
Search method to program your remote.
* Sometimes the fist code that “works” with your device may
operate only a few functions of your device. There may be another code in the
code list that performs more functions. Try other codes from the code list for
more functionality.
* With the Direct Code Entry method, you can program any device
button to control any device in your home entertainment system. For example, you can use the DVR/AUX device
button to control an audio receiver or a DVD, VCR, satellite device, etc.
* For combination devices, you may have to enter a code for each
device. For example, for a VCR/DVD vice, you may have to enter a code for the
DV under the DVD button and enter a code for the VCR using a different
device on the remote. (Write down the code found to operate your device for
future reference.)}}
AUTO CODE SEARCH PROCEDURE
The Auto Code Search searches automatically through all of the
codes stored in this remote. Read all the following steps prior to starting the
auto search as you will need to be prepared to lock-in the proper code when found.
* Manually turn on the device you wish to control.
* Press and hold the SETUP button until the red indicator
light stays on (approximately 4 seconds) and then release the button.
* Press and release the desired device button on the remote (TV,
DVD, CBL/SAT, DVR/AUX). The red indicator will blink once and then remain
on.
* Point the remote at the device and press and release the POWER
button (for TV) or PLAY button (for DVD, VCR, etc.) to start the
search. The red indicator will flash (approximately every 2 seconds) as the
remote searches. [Note: The remote must be pointed at the
device for the duration of this search]
* Place your finger on the #1 button so you are prepared to
lock-in the code..
When the device shuts off or begins playing, press the #1 button
to lock-in the code. The red indicator light will turn off. (Note: You
have approximately two seconds after the device shuts off or begins playing to
lock-in the code.)
* Point the remote at the device and check to see if the remote
operates the device as desired. If it does, no further programming is required
for that device. If it does not, return to step 2 and start the auto search
again.
** Repeat this process for each device (for example TV, DVD, SAT,
AUX) in your home entertainment system you wish to control. Four devices can be
programmed.
{This process may take several minutes as the remote contains
many codes. When using the Auto Code
Search programming method, the device button corresponding to the type of
device you want to control must be selected (for example, the TV device
button must be selected in step 3 if you want to control a TV, the DVD device
button for a DVD player, etc.). The SETUP
button can be used during the search
process to reverse the direction of the search of the remote codes. For example, if you miss the code for your device and the remote is continuing to search (as indicated by the blinking red light), press the SETUP button and the code search will reverse direction and return to the code. Sometimes the fist code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Continue the auto code search as directed above until the best code is found.}
process to reverse the direction of the search of the remote codes. For example, if you miss the code for your device and the remote is continuing to search (as indicated by the blinking red light), press the SETUP button and the code search will reverse direction and return to the code. Sometimes the fist code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Continue the auto code search as directed above until the best code is found.}
Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) will
require you to set up two different Mode buttons to control both parts of the
Combo device. For example, if you have a
TV/DVD Combo, you might need to set up one code under the TV button to
control the TV part AND a separate code (under any other Mode button) to
control the DVD part.
Using SHIFT for Menu and Navigation
The SHIFT button allows access to more than one function
for certain buttons.
Use the SHIFT/SETUP button prior to accessing the MENU,
OK, EXIT and Navigation functions, for example: [For MENU, press
and release SHIFT/SETUP then INFO/MENU.] For OK, press and release SHIFT/SETUP then
MUTE/OK. For EXIT, press and
release SHIFT/SETUP then LAST/EXIT.
For Up, Down, Left or Right Navigation, press and release SHIFT/SETUP
followed by the respective Channel or Volume button. Remote will stay in shift mode until the SHIFT
button is pressed again, or until 10 seconds of inactivity.]
Master Volume Feature
The Master Volume Feature allows you to select a single device
(TV or audio receiver) that the volume control always controls. For example,
the remote can be in TV mode while the volume buttons control the
volume on your audio receiver instead of your TV.
volume on your audio receiver instead of your TV.
Enabling the Master Volume Feature
1 Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
1 Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
2 Press and release desired device button (TV, DVD, SAT, AUX)
for the device you wish to setup to control the volume.
3 Press and release the MUTE button.
4 Press and release the VOL button. The red indicator will blink twice and then go off.
4 Press and release the VOL button. The red indicator will blink twice and then go off.
(To test the feature put the remote in another mode such as the
TV mode if you programmed the audio receiver to be the Master Volume Device.
Point the remote at the audio receiver, press and hold either the VOL UP or the VOL DN button. the audio receiver volume changes then the
remote is programmed correctly. If the
TV volume changes and not the audio receiver, you will have to repeat the steps above and test again.)
Disabling the Master Volume Feature
1 Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
1 Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
2 Press and release the device button (TV, DVD, SAT, AUX)
which is programmed to control the Master Volume Feature.
3 Press and release the MUTE button.
4 Press and release the VOL button. The red indicator light will blink twice and go off.
4 Press and release the VOL button. The red indicator light will blink twice and go off.
Code Identifiation
1 Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
1 Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
2 Press and release the desired device button (TV, DVD,
CBL/SAT, DVR/AUX) you would like the code for.
3 Press and release ENTER button.
3 Press and release ENTER button.
4 Press and release the #1 button. Count the number of times the remote light
flashes. This is the number corresponding to the fist digit of the code. Repeat
the process by pressing the #2, #3 and #4 buttons for the remaining digits.
5 Press and release ENTER button to exit this mode.
5 Press and release ENTER button to exit this mode.
Reset to Factory Settings
1 Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
2 Press and release the MUTE button.
1 Press and hold the SETUP button until the red indicator stays on (approximately 4 seconds) and then release the button.
2 Press and release the MUTE button.
3 Press and release the number #0 button. The red
indicator light will flash twice.
TROUBLESHOOTING
Remote does not operate your device.
* Press the device button of the device you want to control.
* Program the remote with a new code.
* Install new batteries. (You might have to reprogram your remote after installing new batteries.)
* Remote may not be compatible with your device.
* Press the device button of the device you want to control.
* Program the remote with a new code.
* Install new batteries. (You might have to reprogram your remote after installing new batteries.)
* Remote may not be compatible with your device.
Remote does not operate some features of your device.
* Sometimes a particular code might operate some features but not all. Try programming remote with a new code.
* Remote may not be able to operate all features of your device or button names might be different than your device.
* Sometimes a particular code might operate some features but not all. Try programming remote with a new code.
* Remote may not be able to operate all features of your device or button names might be different than your device.
Red Indicator blinks and stays on after you program a product
code.
* Remote did not accept the code.
* Try to program the code again or try a different code.
* Remote did not accept the code.
* Try to program the code again or try a different code.
Remote buttons are not operating properly
* Check to ensure the remote is not in shift mode. Press and release the SETUP/SHIFT button and see if the remote buttons operate properly. If this does not help, press and release the SHIFT/SETUP button again to exit the shift mode.
* Check to ensure the remote is not in shift mode. Press and release the SETUP/SHIFT button and see if the remote buttons operate properly. If this does not help, press and release the SHIFT/SETUP button again to exit the shift mode.
