HOW TO PROGRAM ADB Potenza Remote control - Digital TV remote control programming

Programming Remote Control
Your remote control can handle several devices. However, first you have to set up your remote control for your equipment. You can do this in one of the following ways:
Brand Setup
First, find the manufacturer of your equipment on the Brand Codes list. If the manufacturer’s brand is not listed, go to Automatic Search below. To set up your remote control follow these steps:
1. Turn the device on.
2. Press TV / AUD / DVD / AUX / STB depending on what mode you want to handle and then hold RCU SETUP until the
device key blinks twice.
3. Enter one of the codes from the list. If the code was correct the mode key blinks twice. If not, the key emits one long blink.
Then, you will have to repeat steps 2 and 3 until entering the correct code.
4. Press POWER. If the device has turned off, you have chosen the right code. If none of the codes work, try Automatic
Search.

Automatic Search
Automatic Search should only be undertaken if none of the brand codes works or your brand name is not listed. Use the Automatic Search option.
1. Switch on your device. Then press appropriate mode key, for example TV if you want to set up a TV.
2. Press and hold RCU SETUP until the mode key blinks twice.
3. Press 9 9 1. The mode key blinks twice.
4. Aim the remote at the device and press POWER.
5. Press CH + and CH- repeatedly until the device is switched off.
6. Press POWER to turn the TV on.
7. Next, press RCU SETUP to store the code for your device. The mode key blinks twice. Your remote control is now programmed to operate your TV set.
8. To search codes for other devices repeat steps 1 through 7, but substitute the TV key with the appropriate one for the mode
you are searching for.

Finding Your Code
If you want to know what code operates your device, you can obtain it with the Device Code option. To find out the code, follow these instructions:
1. Switch on your device. Then press appropriate mode key, for example TV if you want to set up a TV.
2. Press and hold the RCU SETUP until the mode key blinks twice.
3. Press 9 9 0. The mode key blinks twice.
4. For the first digit of your code, press 1 and count the number of times the key blinks (e.g. 2 blinks = 2). If the light does not blink, the digit is 0. For the second digit press 2 and count the number of blinks. Do the same for the remaining digits.
5. To check for other device codes, repeat the above steps, but substitute the TV key with the appropriate one for the device you are checking.
Using Learning
Your remote control includes a learning feature. It means you can transfer some unique functions from the remote control of other device to this remote control.
1. Press RCU SETUP until the last selected mode key blinks twice. Then press 9 7 5.
2. Press the mode key. For example to transfer a function from DVD remote control press DVD.
3. Press the key on which the function will be stored.
4. Place your remote control and the device remote control (e.g. your DVD remote control) head-to-head, about 5 centimeters /
2 inches apart.
5. On the device remote, press and hold the key to be learned. The target remote control will blink rapidly and turn off. Keep holding the key on the device remote control until the device key on the target remote blinks twice.
6. If the learning failed, the device key emits one long blink. You will have to repeat step 5.

Deleting a Single Learning Key
Once you have used a particular key to store a new function on it, you may restore the original function of the key.
1. Press RCU SETUP until the last selected mode key blinks twice. Then press 9 7 6.
2. Press the mode key (for example DVD). The mode key blinks twice.
3. Press the key containing the learned function. The mode key blinks twice.
4. Press and hold RCU SETUP to exit programming.
Deleting All Learned Keys
1. Press RCU SETUP until the last selected mode key blinks twice. Then press 9 7 6.
2. Press the mode key twice (for example DVD). All the learned keys for this mode will be cleared. The mode key blinks twice.
3. Press and hold RCU SETUP to exit programming.
Using the Master Power Key
Your remote has a feature that enables you to sequentially turn up to five devices on and off with a single key press. This functionality works only if the remote control is in STB mode.
1. Press RCU SETUP until the last selected mode key blinks twice.
2. Press 9 9 5. The last selected mode key will blink twice.
3. Press POWER.
4. Press the mode key for the device you would like to turn on first and press MASTER POWER. Then press the mode key for the second device to turn on and once again MASTER POWER. Repeat the steps until adding all the devices you want to be operated.
5. To save settings press STB.
6. Next press RCU SETUP to exit programming.
Volume Lock
The remote control enables you to control the volume level of different devices without selecting the mode key for each device. For example: if you are watching a film on your DVD player, you can adjust the volume for your TV set, without pressing the TV mode key on your remote control.
To set the Volume Lock for your TV:
1. Press and hold RCU SETUP until the last selected mode key blinks twice.
2. Press 9 9 3. The last selected mode key will blink twice.
3. Then press TV and the device key blinks twice.
Deleting “Volume Lock” for a particular device (for example for DVD)
1. Press DVD once.
2. Press and hold down the RCU SETUP key until the mode key blinks twice.
3. Press 9 9 3. The mode key blinks twice.
4. Press the VOL- key and the mode key will blink four times.
Now being in DVD mode, you will be able to control VOL+/- or MUTE functions of your DVD only (provided it was volume control).
Deleting “Volume Lock” for all devices
1. Press and hold the RCU SETUP key until the last selected mode key blinks twice.
2. Press 9 9 3.
3. Press the VOL+ key and the last selected mode key will blink four times.
Clearing Custom Programming
You may clear the custom programming and revert to the default settings of the remote control. To do that, follow these steps:
1. Press RCU SETUP until the last selected mode key blinks twice.
2. Enter 9 8 0. The last selected mode key blinks twice, pauses, and blinks twice again.
This procedure does not affect your setup codes. They remain in memory of the remote.

Troubleshooting

Problems & Solution

Device key does not blink when you press a key.  > Replace the batteries with two (2) new AA batteries.
Device key blinks when you press a key, but home entertainment device does not respond. > Make sure you are aiming the remote control at your home
entertainment device and that you are within 4.5 meters / 15 feet of the device you are trying to control.
The remote control does not control home entertainment devices or commands are not performing properly. > Try all listed codes for the device brand being set up. Make sure all devices can be operated with an infrared remote control.
TV/VCR Combo does not respond properly. > Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation.
PLAY and STOP keys do not work on a Motorola DCT-2000 cable converter. Re-program the STB key for cable code 0476.
Tried Search Method and still could not find a working code. > Try the Search Method again after clearing out the device key as follows:
a. Press and hold RCU SETUP until device key blinks twice.
b. Enter 9 9 2.
c. Press and release the device key to be cleared twice.
Remote control does not turn on Sony or Sharp TV/VCR Combo. > For power on, these products require programming TV codes on the remote control. For Sony, use TV code 0000 and VCR code 0032. For Sharp, use TV code 0093 and VCR code 0048.

How to Set-Up eLife TV One for All UNIVERSAL REMOTE CONTROL

The default Set Top Box protocol may be programmed in the field using the following procedure

Press the <Home> key, <REC> key and <OK> key simultaneously for 3 sec, STB indicator LED will give a conformation blink and remain on.

Release the keys and press a <Digit> key to select the Default Protocol.  Refer to the table below for the protocol selection.

The LED will blink, indicating that the Default STB Protocol has been programmed; the number of blinks corresponds to the Protocol number selected, i.e. 1 blink for Protocol 1, 2 blinks for Protocol 2, etc.

The Set top box protocol can be changed in the field to retune the RCU to another STB using the following procedure:

Press and hold key ‘Home’ and the relevant digit key together for a minimum of 3 seconds, until the STB indicator LED blinks two times (of 500 ms each).  The new STB protocol is now programmed to non-volatile memory.

Power on the STB and try out the dedicated STB buttons. If there is no reaction on the STB, repeat the previous steps, for each code listed below

Set-up procedure

Switch on your TV

Press and hold the TV button on your remote for 5 seconds. The TV button will light up.

Look up the 4-digit code for your brand in the adjacent shortlist of brands.  Enter the 4-digit codes using the digit buttons.

Press and hold the Power button. Release the button immediately as soon as the TV switches off.  (This step normally takes between 5 and 60 seconds).

Switch On your TV. Try out the volume channel buttons on your remote. If those buttons are not working on your remote control, repeat step4. until some button works. [You can also learn the buttons from your original remote.]

Press the TV button twice (2x) to finish setup.  {If you made a mistake: Press the TV button twice to exit setup.  The red light under the TV button turns off. Restart from the beginning}

If your brand is missing in this shortlist, look at the complete BRAND LIST.

Use '9999' as 4-digit code in case you cannot find your brand in the BRAND LIST in the user manual. Note that ‘9999’ may result in a long setup (up to 15 minutes)

Turn on the TV/Audio

Press and hold the <TV> key for 3 seconds; until the setup LED lights up.  This enables the protocol and brand selection function for the TV device, the mode LED will remain on. To enable selection for AUX device, press <Mute> key after hold <TV> key for 3 secs , the TV-mode led will give a Set-up Confirmation blink.

Release the key and enter the 4-digit Brand-id (please refer to brand ID table guide) for the TV/AUX by pressing each digit key in sequence.  With the first 3 digits, the device-LED will give a reverse blink.  At the fourth digit, the device LED gives two reverse blinks and remains on (the search will include all code sets that are linked to the selected brand, or it will search through all code sets in the universal database if brand number 0000 was selected).

Press the <POWER> or <MUTE> key continuously; after 5 secs a power or mute IR-command is transmitted for the next universal code-set in the code-set list for the selected brand. The device-LED will turn off during transmission of the IR-command. When the <POWER> or <MUTE> key is held continuously then subsequent universal code-sets will be selected automatically and a sequence of standby or mute IR-command of the next universal code-set is transmitted.  [In the case that brand number 0000 was selected the whole database of either TV or Aux is scanned. The device-LED shows a reverse blink for each transmission.]

Press TV twice to confirm the code. The code that was selected when TV was pressed twice or when 4 sec timeout happened is the code that will be programmed into the remote. The RC will give a set-up confirmation blink and go back to normal operation.

All LEDs are turned off. 

Universal code number “0000” will trigger a search through all codes available in the remote independent of the brand.

Timeout for 4 seconds happened if the user hasn’t pressed the TV key twice to confirm the code. The code will be programmed into the remote; the RC will give a set-up confirmation blink and go back to normal operation.

During the setup, if user wants to restart TV device set-up, can press and holding the <TV>key for 3 sec (step ii);if user want to restart AUX device,
can press <Mute> after holding the <TV> key for 3 sec, then the set-up start from the beginning of the auto set-up again.

In the case that brand number 0000 was selected the whole database of either TV or Aux is scanned. The device-LED shows a reverse blink for each
transmission.

Note that the search sequence continues by going through the whole list after scanning through the brand list when all code-sets for the brand are
tested. It only stops when all code-sets of the whole database are tested.

When the TV/AUX turns off or mute, the user must release the POWER or MUTE key. The user should switch the TV/AUX on again with the original or
the universal remote control it device turn off. Now all keys can be tried out with the universal remote control (inverse blinking if a universal function-code is available under the key) including the POWER and MUTE key. Press <POWER> or <MUTE> for 5 secs to continue the code-set selection.

If the 4 digit code is wrong or if another key than the <POWER> or <MUTE> key is pressed after the 4 digits, Auto brand search will be exited and the unit will not change the universal code-set number for the respective device.

Exiting a successful setup is via pressing the TV mode key twice or after timeout.

After TV/Aux is also setup in addition to Etisalat STB set-up with the remote, the remote control will control the volume of the TV/Aux only and the STB volume control will not be managed from the remote any more.  In case one prefers however to continue to control the volume via the STB and want the volume control to work for TV/Aux when selecting TV (pressing TV) and volume control to work for STB when selecting STB (pressing Home), the following need to be performed once.  Press Home and Mute simultaneously for 5 seconds until the light under the TV keys blinks twice.  With the above steps you can toggle between TV/Aux and STB and there will be volume control for TV while in TV mode and Volume control for STB when in STB/Home mode.